Leading 10 usual forklift crashes ， forklift operation should pay attention to these issues ！.
Leading 10 usual forklift crashes ， forklift operation should pay attention to these issues ！.
Blog Article
Do not ignore the forklift at the workplace. If the operation is bad, there will be significant accidents in minutes, and there are numerous accidents including forklifts.
Situation 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift cargo exceeds the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.
Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and after that start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist should initially validate that the tons is stable and trusted.
4. The start has to be slow and consistent.
Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to turn off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the tons need to not block the driver's sight. In unique conditions, when the thing impacts the forward vision, drive at a low rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.
packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be set up to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.
Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the hand brake handle to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond Stand-on Electric Pallet Stacker 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak needs to additionally be inspected and the seals ought to be replaced in time.
Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp Electric Forklift Truck for Warehouse to avoid the tendency of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the gradient. When the slope is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they come across large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not enabled to get the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Sections with a longitudinal incline greater than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the same length as the challenge must be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844